Synrad Firestar V30 CO2 laser - Revision history

Aplstudent: /* Synrad Firestar V30 CO2 laser */

2020-02-26T23:59:29Z

‎Synrad Firestar V30 CO2 laser

Aplstudent: /* Synrad Firestar V30 CO2 laser */

2020-02-26T23:19:06Z

‎Synrad Firestar V30 CO2 laser

Aplstudent: /* Synrad Firestar V30 CO2 laser */

2020-02-25T20:39:19Z

‎Synrad Firestar V30 CO2 laser

Aplstudent at 20:38, 25 February 2020

2020-02-25T20:38:11Z

Admin: Created page with "==== Synrad Firestar V30 CO2 laser ==== Wavelength: 10.2-10.8 μm
Output power: 30 W
Power Stability: +- 5% (cold start), +-3% (after two minutes)
Continuous W..."

2020-02-23T17:18:20Z

Created page with "==== Synrad Firestar V30 CO2 laser ==== Wavelength: 10.2-10.8 μm Output power: 30 W Power Stability: +- 5% (cold start), +-3% (after two minutes) Continuous W..."

New page

==== Synrad Firestar V30 CO2 laser ====

Wavelength: 10.2-10.8 μm 
Output power: 30 W 
Power Stability: +- 5% (cold start), +-3% (after two minutes) 
Continuous Wave (CW) 
Polarization: Linear, horizontal 
Beam Diameter: 2.5 +- 0.5 mm (<math>1/e^2</math>) 
Rise Time < 100 μs

← Older revision		Revision as of 23:59, 26 February 2020
Line 11:		Line 11:
	Rise Time < 100 μs <br>		Rise Time < 100 μs <br>

−	~~'''~~Start-up Procedure~~:'''<br>~~	+	[[Start-Up Procedure]]

−	~~1. Make sure lab door is closed, and don appropriate eye protection.~~
−
−	~~2. Turn on power strip. (This should only turn on the UC-2000 controller, everything else should still be off).~~
−
−	~~3. On UC-2000 Controller:~~
−	* Hold the 'SELECT' and 'ENTER' buttons down to enter 'Setup Mode'.
−	* Set Frequency to 5 kHz, Gate Pull to 'Up', Maximum PWM to 95%, Lase On Pwr-Up to 'N', Checksum to (On). Use the 'SELECT' <br>
−	~~: button to switch between options and the 'ENTER' button to change the setting selected. Once finished, select 'SAVE AND EXIT' <br>~~
−	~~: and hit the 'ENTER' button on the controller.~~
−	* Set mode to manual by hitting the 'SELECT' button on the main screen until 'MANUAL' option comes up, and hit 'ENTER'. <br>
−	~~: (Make sure not to select 'MANUAL CLOSED', as this may not operate in output intended if not in the recommended range.)~~
−	* Turn adjustment knob until PWM is set to 0.0%.
−
−	~~4. Turn on power supply unit for cooling fans. Turn coarse voltage to ~12V, and current to ~0.5A. (The maximum power rating of each~~
−	~~:is 24V @ 0.46A each, and can be increased as needed if laser begins to heat during operation.)~~
−
−	~~5. Turn on power supply for Laser. Set voltage to 30V and turn knob for current all the way to the right. The current will not appear~~
−	~~:to rise at this point, but when the laser is turned on it will draw as much current as necessary for the set PWM %.~~
−
−	~~6. Remove aperture dust cover.~~
−
−	~~7. Set PWM to 1.0% and toggle 'LASE' to 'ON'. You can confirm the laser is in operation by the red LED being lit on the rear of the~~
−	~~:laser. Using an IR Detector card, ensure beam is aligned with an appropriate beam block or power meter, ensuring the beam does~~
−	~~:not go past the table.~~
−
−	~~8. Once beam is safely aligned, this is now ready to use.~~

@@ Line 8: / Line 8: @@
 Polarization: Linear, horizontal <br>
 Beam Diameter: 2.5 +- 0.5 mm (<math>1/e^2</math>)<br>
 Rise Time < 100 μs <br>

@@ Line 1: / Line 1: @@
 ==== Synrad Firestar V30 CO2 laser ====
 Wavelength: 10.2-10.8 μm <br>
 Output power: 30 W <br>
@@ Line 8: / Line 9: @@
 Beam Diameter: 2.5 +- 0.5 mm (<math>1/e^2</math>)<br>
 Rise Time < 100 μs <br>
 Useful Links:<br>
 [[Media:Operators_Manual_v30.pdf| Firestar V30 Users Manual]]<br>
 [[Media:Operators_Manual_UC2000.pdf| UC2000 Controller Users Manual]]<br>

← Older revision		Revision as of 20:38, 25 February 2020
Line 8:		Line 8:
	Beam Diameter: 2.5 +- 0.5 mm (<math>1/e^2</math>)<br>		Beam Diameter: 2.5 +- 0.5 mm (<math>1/e^2</math>)<br>
	Rise Time < 100 μs <br>		Rise Time < 100 μs <br>
		+
		+	Useful Links:<br>
		+	[[Media:Operators_Manual_v30.pdf\| Firestar V30 Users Manual]]<br>
		+	[[Media:Operators_Manual_UC2000.pdf\| UC2000 Controller Users Manual]]<br>

Synrad Firestar V30 CO2 laser - Revision history

Aplstudent: /* Synrad Firestar V30 CO2 laser */

Aplstudent: /* Synrad Firestar V30 CO2 laser */

Aplstudent: /* Synrad Firestar V30 CO2 laser */

Aplstudent at 20:38, 25 February 2020

Admin: Created page with "==== Synrad Firestar V30 CO2 laser ==== Wavelength: 10.2-10.8 μm Output power: 30 W Power Stability: +- 5% (cold start), +-3% (after two minutes) Continuous W..."

Admin: Created page with "==== Synrad Firestar V30 CO2 laser ==== Wavelength: 10.2-10.8 μm
Output power: 30 W
Power Stability: +- 5% (cold start), +-3% (after two minutes)
Continuous W..."