Electronics - Revision history

Wikiuser at 23:48, 21 March 2014

2014-03-21T23:48:42Z

Wikiuser at 23:39, 21 March 2014

2014-03-21T23:39:03Z

Wikiuser at 22:59, 21 March 2014

2014-03-21T22:59:13Z

Wikiuser at 22:48, 21 March 2014

2014-03-21T22:48:52Z

Admin at 22:28, 21 March 2014

2014-03-21T22:28:20Z

Admin at 22:22, 21 March 2014

2014-03-21T22:22:36Z

Admin at 22:07, 21 March 2014

2014-03-21T22:07:46Z

Admin at 22:03, 21 March 2014

2014-03-21T22:03:55Z

Admin at 21:39, 21 March 2014

2014-03-21T21:39:48Z

Admin at 21:14, 21 March 2014

2014-03-21T21:14:18Z

@@ Line 177: / Line 177: @@
 *1kHz                     Tone Pot 0%
 [[File:1khz1vpptone0.jpg|400px|left]]  Tone Pot 100% [[File:1khz1vpptone100.jpg|450px|right]]
@@ Line 187: / Line 194: @@
 *4kHz                     Tone Pot 0%
 [[File:4khz1vpptone0.jpg|400px|left]]  Tone Pot 100% [[File:4khz1vpptone100.jpg|450px|right]]
@@ Line 194: / Line 208: @@
 Trends: Higher frequencies are more heavily clipped, and louder high frequencies have a nearly symmetric waveform. Lower frequencies are less clipped and exhibit more asymmetric behaviour.

@@ Line 171: / Line 171: @@
-Note the asymmetry of both waveforms. With the drive at 0%, the wave almost resembles a sine wave. The 100Hz waveform is not very heavily clipped when the drive pot is at 100%
+Note the y-axis asymmetry of both waveforms. With the drive at 0%, the wave almost resembles a sine wave. The 100Hz waveform is not very heavily clipped when the drive pot is at 100%
 *1kHz                     Tone Pot 0%
-[[File:1khz1vpptone0.jpg.jpg|400px|left]]  Tone Pot 100% [[File:100hz1vppdrive100.jpg|450px|right]]
+[[File:1khz1vpptone0.jpg|400px|left]]  Tone Pot 100% [[File:1khz1vpptone100.jpg|450px|right]]
-Note the asymmetry of both waveforms. With the drive at 0%, the wave almost resembles a sine wave. The 100Hz waveform is not very heavily clipped when the drive pot is at 100%
+Note the y-axis asymmetry switches sides between waveforms. With the tone at 0%, the wave resembles a triangle wave. The 1kHz waveform is heavily clipped when the tone pot is at 100%

@@ Line 146: / Line 146: @@
 When the Tone Potentiometer is all the way to the bass side, The opamp has a gain of 1k/1k=1. The components R7, C5, and C6 create a low pass filter with a cutoff frequency 360Hz, which is low in the hearing range (20-20kHz).
 When the Tone Potentiometer is all the way to the treble side, the opamp has a gain of 1+1k/Z(R8+C6), the impedance of R8 and C6. This impedance will be low for high frequencies, and high for low frequencies, resulting in a treble boost. The cutoff frequency for R8 and C6 is 3.25kHz.
@@ Line 161: / Line 165: @@
 Now that we understand how the circuit works, lets look at the data I took with an oscilloscope. The input is a sine wave, and the voltage is set at 1V peak to peak.
-Hz
+*100Hz                     Drive Pot 0%
-[[File:100hz1vppdrive0.jpg|400px|left]] [[File:100hz1vppdrive100.jpg]]
+[[File:100hz1vppdrive0.jpg|400px|left]]  Drive Pot 100% [[File:100hz1vppdrive100.jpg|450px|right]]
 Note the asymmetry of both waveforms. With the drive at 0%, the wave almost resembles a sine wave. The 100Hz waveform is not very heavily clipped when the drive pot is at 100%

@@ Line 16: / Line 16: @@
 So if we are sending a clean signal into the effect, what will come out?
 *To answer that question we will look at what the circuit is, qualitatively and quantitatively.
 Qualitatively:
@@ Line 65: / Line 70: @@
@@ Line 79: / Line 98: @@
@@ Line 94: / Line 109: @@
@@ Line 144: / Line 160: @@
 Now that we understand how the circuit works, lets look at the data I took with an oscilloscope. The input is a sine wave, and the voltage is set at 1V peak to peak.

← Older revision		Revision as of 22:28, 21 March 2014
Line 130:		Line 130:
	When the Tone Potentiometer is all the way to the bass side, The opamp has a gain of 1k/1k=1. The components R7, C5, and C6 create a low pass filter with a cutoff frequency 360Hz, which is low in the hearing range (20-20kHz).		When the Tone Potentiometer is all the way to the bass side, The opamp has a gain of 1k/1k=1. The components R7, C5, and C6 create a low pass filter with a cutoff frequency 360Hz, which is low in the hearing range (20-20kHz).
	When the Tone Potentiometer is all the way to the treble side, the opamp has a gain of 1+1k/Z(R8+C6), the impedance of R8 and C6. This impedance will be low for high frequencies, and high for low frequencies, resulting in a treble boost. The cutoff frequency for R8 and C6 is 3.25kHz.		When the Tone Potentiometer is all the way to the treble side, the opamp has a gain of 1+1k/Z(R8+C6), the impedance of R8 and C6. This impedance will be low for high frequencies, and high for low frequencies, resulting in a treble boost. The cutoff frequency for R8 and C6 is 3.25kHz.
		+
		+
		+
		+
		+
		+
		+
		+
		+
		+
		+
		+
		+
		+	Now that we understand how the circuit works, lets look at the data I took with an oscilloscope. The input is a sine wave, and the voltage is set at 1V peak to peak.

← Older revision		Revision as of 22:22, 21 March 2014
Line 116:		Line 116:
	[[File:Active_Tone-Volume_Stage.gif\|left]]		[[File:Active_Tone-Volume_Stage.gif\|left]]

−	The Volume Stage simply bleeds off some of the output to ground. The Tone Stage is a non-inverting opamp. To understand the Tone Stage, let's look at the	+
		+
		+
		+
		+
		+
		+
		+	The Volume Stage simply bleeds off some of the output to ground. The Tone Stage is a non-inverting opamp. To understand the Tone Stage, let's look at the Tone Pot turned to both extremes.
		+
		+	[[File:Tone_Control_Example.png\|left]]
		+
		+
		+	When the Tone Potentiometer is all the way to the bass side, The opamp has a gain of 1k/1k=1. The components R7, C5, and C6 create a low pass filter with a cutoff frequency 360Hz, which is low in the hearing range (20-20kHz).
		+	When the Tone Potentiometer is all the way to the treble side, the opamp has a gain of 1+1k/Z(R8+C6), the impedance of R8 and C6. This impedance will be low for high frequencies, and high for low frequencies, resulting in a treble boost. The cutoff frequency for R8 and C6 is 3.25kHz.

← Older revision		Revision as of 22:07, 21 March 2014
Line 108:		Line 108:

	To understand the Clipping Amp, let's start from scratch and build up from there. We start with the Opamp and the resistors. This is a non-inverting opamp with a gain 1+(51k+Pot)/4.7k. So the gain ranges from 12 to about 120. However, when we add the diodes to our circuit, the gain doesn't matter anymore. Under .6 Volts, the diodes do not conduct electricity, but above .6 Volts, the diodes act like a short circuit to the (51k+Pot) effective resistance. This creates a clipped sine wave with a steep slope, and is the basis of diode-clipping distortion effects. Next we add in a couple capacitors to filter the frequency response. the .047uF capacitor in series with the 4.7k resistor creates a high pass filter with a frequency 720Hz. This attenuates lower frequencies out of the Clipping Stage, resulting in a cleaner signal (This is simply a human aesthetic preference). This capacitor also causes a phase shift in the signal, resulting in asymmetrical clipping (another human aesthetic preference). The 51pf capacitor in parallel with the diodes acts as a low pass filter, attenuating higher frequencies and thus softening the clipped edges of the waveform. This makes the distortion seem less harsh.		To understand the Clipping Amp, let's start from scratch and build up from there. We start with the Opamp and the resistors. This is a non-inverting opamp with a gain 1+(51k+Pot)/4.7k. So the gain ranges from 12 to about 120. However, when we add the diodes to our circuit, the gain doesn't matter anymore. Under .6 Volts, the diodes do not conduct electricity, but above .6 Volts, the diodes act like a short circuit to the (51k+Pot) effective resistance. This creates a clipped sine wave with a steep slope, and is the basis of diode-clipping distortion effects. Next we add in a couple capacitors to filter the frequency response. the .047uF capacitor in series with the 4.7k resistor creates a high pass filter with a frequency 720Hz. This attenuates lower frequencies out of the Clipping Stage, resulting in a cleaner signal (This is simply a human aesthetic preference). This capacitor also causes a phase shift in the signal, resulting in asymmetrical clipping (another human aesthetic preference). The 51pf capacitor in parallel with the diodes acts as a low pass filter, attenuating higher frequencies and thus softening the clipped edges of the waveform. This makes the distortion seem less harsh.
		+
		+
		+
		+
		+
		+
		+	[[File:Active_Tone-Volume_Stage.gif\|left]]
		+
		+	The Volume Stage simply bleeds off some of the output to ground. The Tone Stage is a non-inverting opamp. To understand the Tone Stage, let's look at the

@@ Line 25: / Line 25: @@
 [[File:0321141432-00.jpg|thumb|400px|left|And this is how it looks in an enclosure]]
@@ Line 31: / Line 81: @@
 Quantitatively:
 *This is the circuit diagram:
-[[File:Tube_Screamer_Anatomy.gif|400px|left]]
+[[File:Tube_Screamer_Anatomy.gif|thumb|800px|left]]

@@ Line 7: / Line 7: @@
 I want to understand what makes overdrive sound good. Oftentimes, when people speak of "distortion", they are talking about noise that is unwanted, but with guitars, there is a good distortion, which make the guitar signal sound good. As I built the pedal, I analyzed it with an oscilloscope, as well as did research, to better understand what makes it sound qualitatively good to human ears.
-*Basic Guitar Physics*
+Basic Guitar Physics
-An electric guitar works by converting sound into an alternating current, using pickups. A pickup is a magnet with wire densely coiled around it. It creates a magnetic field around the guitar string, so that when the string vibrates, there is a change in the magnetic field, and a voltage is created in the coiled wires.
-[[File:Pickup Schematic.gif]] [[File:Fender_guitar_pickups.jpg]]

← Older revision		Revision as of 21:14, 21 March 2014
Line 6:		Line 6:
	Why build a guitar pedal?		Why build a guitar pedal?
	I want to understand what makes overdrive sound good. Oftentimes, when people speak of "distortion", they are talking about noise that is unwanted, but with guitars, there is a good distortion, which make the guitar signal sound good. As I built the pedal, I analyzed it with an oscilloscope, as well as did research, to better understand what makes it sound qualitatively good to human ears.		I want to understand what makes overdrive sound good. Oftentimes, when people speak of "distortion", they are talking about noise that is unwanted, but with guitars, there is a good distortion, which make the guitar signal sound good. As I built the pedal, I analyzed it with an oscilloscope, as well as did research, to better understand what makes it sound qualitatively good to human ears.
		+
		+	Basic Guitar Physics
		+
		+	An electric guitar works by converting sound into an alternating current, using pickups. A pickup is a magnet with wire densely coiled around it. It creates a magnetic field around the guitar string, so that when the string vibrates, there is a change in the magnetic field, and a voltage is created in the coiled wires.
		+	[[File:Pickup Schematic.gif]] [[File:Fender_guitar_pickups.jpg]]